Bright & BeautifulChoose from our wide range of classic and contemporary lighting designs handmade in our Yorkshire workshop. Our range of wrought iron lighting is unique and not available anywhere else.
Posted By Elizabeth Stocker
21 February 2015
Dawn, Sheena, Katie and I all made tadpoles to use as ornamentation for the bench Nigel and the blacksmiths were making to commemorate our friend Andre’s life.
Dawn’s daughter Alice asked if she could make one too. Here is how she did it:
Andrew had prepared a kit for her – a 25mm solid steel sphere welded to a rod, to make into the head, and a strip of 13mm by 3mm flat steel to make the tail from.
Andrew starts by describing how they would be shaping them:
Alice gets a lesson in how to use a hammer
Alice heats a sphere in the forge to a bright orange heat – about 800 degrees. At every stage, Andrew demonstrates what he wants Alice to do using another sphere.
Andrew wants Alice to forge her red hot sphere into an elongated cubical shape.
The steel is soft enough to work for about half a minute after coming out of the forge, and then needs heating up again. After about ten sessions in the forge, Alice gets the shape right.
Alice’s hand develops a blister, so I administer first aid – a plaster. Poor Alice – there is a big difference between the size, strength and hardness of a girl’s hand to Andrew’s hand.
The head is left to cool and Alice starts to work on shaping the tail into a narrowing tapering shape. After reheating the steel many times, this is achieved to both of their satisfaction.
Andrew introduces Alice to a different kind of hammer – a cross pein – this one has a long sharp face to make indentations in the steel, rather than to flatten it. He draws a diagram onto the anvil of the pattern of ridges which should be on the sides of the tail – to make it seem more lithe and fish-like.
Alice manages this, cools the tail in the water-bath and cuts off the rest of the flat steel with the guillotine.
They had found time for a few laughs along the way.
The head is now cool, and Alice marks the eyes with a felt tip pen, and makes them indented with a punch.
Andrew buffs up the head a little with an angle grinder, and then Alice cuts the head off the rod with a hacksaw.
The head and the tail are ready.
Andrew welds them together in the welding booth and then cleans up the weld with an angle grinder.
He then heats small sections of the tail with a gas torch for Alice to make the bends in it with a small hammer – to make it look wriggly. The tail has to be reheated to make each bend.
Alice cools the tadpole in the water-bath and buffs it up with a wire brush.
Job done! Well done Alice and well done Andrew!
Alice with Andre’s bench – her tadpole is in there somewhere and was galvanised with the rest of it.
Back to news...
7 Feb 2018- A Yorkshire blacksmith in Pari...
16 Dec 2017- The White-faced Woodland – i...
23 Nov 2017- St Clement - the patron saint ...
10 Nov 2017- In celebration of our churches
9 Oct 2017- Inside a Yorkshire Shepherd's ...
18 Aug 2017- Come and see us at Penistone S...
4 Aug 2017- 'At the anvil - keeping ironwo...
3 Aug 2017- The Maythorne Pendant - introd...
1 Aug 2017- Throwing some light on the sub...
16 Mar 2017- Enoch the Power Hammer
22 Nov 2016- A week in the life of a rescue...
9 Sep 2016- Metalwork lessons in the 1960'...
16 Jun 2016- The Northern Powerhouse
5 May 2016- Cannon Hall's Cannons
11 Nov 2015- Elizabeth’s Moonlighting Job
14 May 2015- Harmonious Blacksmiths
23 Mar 2015- Sheep May Safely Graze
18 Mar 2015- Andre's bench
21 Feb 2015- Alice's tadpole
14 Feb 2015- The Blacksmith’s Bistro
14 Jan 2015- Naming Our Designs